Wednesday, September 23, 2020

EJ22 airbox into EA81 Brat

 The 1995 Legacy airbox that came with my donor car has an angled snorkel and did not fit great in the Brat body.  I pulled a snorkel and air box from a 92 legacy that fits much better, the MAF meets the airbox at 90deg instead of 45 which works better for the space.  I had to remove my AC relays from the strut tower and reroute (lower) the factory wiring harness from the Brat to get it in place, but it looks good and secure.  The only problem was the inlet to the filter on the under side of the box was almost flat against the fender.  I could have drilled into the fender to supply air but decided I would put speed holes into the lower box instead. 



I had to cut off the mounting feet from the bottom of the housing to make it fit so I need to attach it to the Brat somehow, but I don't expect that to be a big problem. 

Tuesday, September 22, 2020

EJ22 Pitch stopper

 The EA81 engine in my Brat had a pitch stopper, and so do the EJ22 and EA82 engines.  The EA81 pitch stopper is not in the same place or same design as the more modern ones, so I had to modify mine to fit the new EJ motor.  I cut it shorter and welded it back together, and then drilled a piece of flat bar to bolt onto the adapter plate that mates my full time 4wd transmission from an EA82 GL10 Turbo to the EJ motor from the Legacy.   

The stock brat mount remains unmodified.  I guess the purpose is to prevent the motor from shifting with torque.  Some don't run them after conversion, mine was easy enough to make that it might as well go in. 

The Brat sat under a cover indoors for the last few years, thankfully it survived without any major damage, but it did accumulate a large amount of mouse crap.  Thankfully they didn't seem to ruin my new carpet or seats. 

Sunday, September 20, 2020

Surge tank & high pressure fuel pump

A carburetor has a bowl of fuel to draw from in the event that the fuel pump sucks some air if the fuel in the tank is low  and sloshing around.  In a fuel injected car, there is no reserve and the fuel must be supplied at a specific pressure, so any air in the line from sloshing is bad. Fuel injected cars have baffles to trap the fuel around the pickup in the tank, but they are not present in a car designed for a carburetor.  There was a turbo brat with fuel injection for 2 years (I think) that had a baffled tank and would bolt in, but they are much more rare than a regular brat, especially 38 years later, so impractical to find.  So I'm installing a surge tank, which is essentially a small bowl of fuel that feeds the high pressure pump, keeping a steady supply.  Race cars typically use aluminum or stainless and that all seemed out of place in a cheap old car.  I settled on the following solution.  A marine fuel filter / water separator that has the necessary 4 ports already was a great place to start. 

 

The existing low pressure fuel pump supplies gas into the filter.  The high pressure pump draws from the filter.  The return from the fuel rail returns to the filter.  When the filter is completely full then the fuel returns to the tank.  I had to modify the fuel filter bracket just a little.  The two "in" ports are independent of each other, but the "out" ports are connected by the casting.  I tapped the casting on the overflow "out" and put a set screw in it to separate it from the high pressure pump feed "out".  I then had to drill into the casting after my plug to open up the overflow "out" so it would allow a full filter to return to the tank.  To mount it all, I decided on the drivers fender where the old jack holder was.  

I bent a bracket from 16 ga steel to support the filter, and then made a fuel pump bracket from 20 ga and used the toggle clamp from the stock fuel filter to close it. There is a rubber strip around the filter to dampen vibration and also hold it snug in the metal clamp.

 I've got both brackets screwed in for fit up, once I'm "finished" I'll go back and tack them in place.  I've got all the the lines mocked up with whatever hose I had lying around, I'll replace them with appropriate new fuel line and then I'll have the fuel system sorted! 





Some of the EJ swap write ups claim the stock return line is too small, but I'll give it a try and if it not able to keep up with the return feed I'll run a larger return line.  The stock brat return line is 1/4" and the supply is 5/16" by my measure.  I don't want to drop the tank and install a bigger bulkhead fitting for return, but I will if its necessary.  




Thursday, September 17, 2020

EJ Start -


 This motor has not run in 6 years, what a great engine!

Resurrection - Brat & Blog




 To bring everyone up to speed, the motor swap was a larger project than I anticipated, and after several years of procrastination, my friends agreed to come help me finish this bad boy.  The EJ starts and runs.  Now I need to do a few finishing problems.  Here is a list of my problems, and I"ll make a post of each of my solutions so that this blog might be a good reference in years to come.  Since I started this swap, Photobucket broke the internet and sank most the useful forum posts.  So hopefully blogger never follows suit.  


Things needed to finish my EJ 2.2 Swap into my 1982 Brat EA81.  

  • I need to adjust the front anti sway bar, the hump hits my full time 4WD 5 speed from a GL10 turbo wagon.  
  • Fuel - surge tank and high pressure fuel pump
  • Exhaust - attach cat, oxygen sensors & muffler
  • Integrate the wiring harness and ECU into the Brat in a clean fashion
  •  Radiator & cooling setup
  • Install Oil pressure and Temperature sending units that work with the Brat gauges
  • Air box install
  • Battery relocate

Saturday, March 15, 2014

Transmission swap




I'm trying to go from 4 speed to 5 and to do that with my 5speed 25 spline transmission, I need to swap in some 23 spline output shafts.  However, the 23 spline output shafts from my 4 speed are more or less 27mm and the ones from the turbo are 30mm.  Dang.

Saturday, March 9, 2013

GL10: Organ donor







I got a GL10 from a good friend, and today I removed everything I wanted.  I plan to use the 5 speed FT4WD transmission in my Brat, due to the taller gear ratio.  The 82 brat had a ridiculous low gearing, so it does not like to go 70.  They changed the gear ratio starting in 83, so I'm doing myself a favor.  It will be sweet to have full time 4wd, the car seems to accelerate and track better in 4wd, but because it was real 4wd I couldn't use it on dry pavement.  The FT4WD was made for pavement, and the best part, it has a vacuum operated locking center differential, so I can still have real 4wheel drive for off road.  Hooray!  Now I need to dispose of this car!  It was a shame to take it apart, it was in pretty good shape, but no paperwork and a crappy turbo engine mean it is going to a better place to let my Brat live a better life.